Huge Energy Savings in furniture Manufacture with Central Vacuum Supply

Maulburg, Germany ADA Möbelfabrik, headquartered in Anger (Austria), is one of Europe’s largest manufacturers of furniture. Upholstered furniture, beds, mattresses and slatted frames are produced for the Austrian market and for many other European countries in two shifts, using modern manufacturing techniques. The vacuum supply required for securing items to the CNC machining centres is provided via a central vacuum plant produced by Busch Austria. By opting for this vacuum system, ADA has integrated an extremely economical and reliable vacuum supply into the production process.
One of the two CNC processing centres with NBM clamping tables

Starting from humble beginnings as a rope manufacturer in around 1900, ADA has evolved into an ultramodern furniture producer that is still run as a family firm. In addition to its factory in Anger, ADA also has production sites in Hungary (in Körmend and Nova) and Romania. Until 2009, there were two CNC portal machining centres installed at the production site in Anger with grid-based clamping tables for NBM (nested-based manufacturing), featuring two dry running rotary vane vacuum pumps on each table and a suction capacity of 500 cubic metres per pump per hour. These vacuum pumps were continuously in use across the two shifts and as they were each powered by 15-kW electric motors they consequently consumed a large amount of energy. Furthermore, the vanes in the rotary vane vacuum pumps had to be replaced once a year due to wear. The management at ADA therefore decided to look for a more economical alternative for their vacuum supply system and they placed particular importance on obtaining a new CNC router, which would be equipped with two additional rotary vane vacuum pumps with 4-kW motors. They consequently looked into our Mink claw vacuum pump technology in close detail.

In contrast to regular rotary vane vacuum pumps, Mink claw vacuum pumps from Busch operate using a non-contact process. This means that the rotating parts within the vacuum pump do not touch each other. The advantage of this is that the Mink claw vacuum pump creates a vacuum without any wear occurring, so no operating fluids, such as oil or water, are required in the compression chamber. The need for maintenance and part replacement is reduced to a minimum. The only maintenance task that remains is an oil change in the gear unit, which must be performed after every 20,000 operating hours. A further advantage of Mink claw vacuum pumps is that, thanks to their non-contact operation, they use less motor power, which in turn has a highly positive effect on energy consumption. During the discussions with Busch Austria the idea of centralising the vacuum supply was put forward.

Busch Austria therefore designed a customised central vacuum system for ADA, consisting of eight identical Mink claw vacuum pumps, each equipped with a suction capacity of 300 cubic metres per hour. This vacuum system provides a sufficient vacuum supply to the two CNC machining centres with NBM clamping tables and to the additional machining centre with vacuum blocks An additional Mink acts as a back-up pump. This pump is hardly ever used, but if required it can be used to increase the suction capacity of the system such that an additional CNC router can be connected to the vacuum supply.

The suction capacity required varies greatly and is dependent to a large extent on the materials used and the size of the work pieces. For example, when materials with a high level of air permeability are being machined simultaneously on each of the three connected machining centres, a higher suction capacity will be required than when solid wood is being machined on all machines at once. The control system for the vacuum system is therefore designed in such a way that at any one time only the pumps required to supply the power currently needed are in operation. All other pumps are automatically switched off.

The energy consumption level for the vacuum supply system would have added up to 68 KW in the case that, with the two portal machining centres each equipped with two 15-kW rotary vane vacuum pumps, the proposed CNC router was installed, featuring two further, small rotary vane vacuum pumps, each with 4-kW motors. The central vacuum system supplied by Busch requires 44 kW for the eight Mink claw vacuum pumps, which represents a theoretical energy saving of 35 percent. Thanks to the on-demand control system, the individual Mink vacuum pumps are only in operation for an average of 10 hours out of the 16 hours of the two shifts. This enables a further energy saving of approx. 38 percent.

The Mink vacuum system from Busch has been in operation since May 2009 and it has been running fault-free since that time. By the end of 2009, the management team at ADA had already thought about purchasing another vacuum system for the production site in Körmend (Hungary) due to the cost-efficiency and reliability they had experienced with their existing Busch vacuum system.


Categories
Want to know more?
Contact us directly (Busch United Kingdom):
+44 (0)1952 67 74 32 Get in contact